HT12E DATASHEET IN PDF

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Sadal Kejind
Country: Timor Leste
Language: English (Spanish)
Genre: Video
Published (Last): 4 February 2009
Pages: 350
PDF File Size: 1.29 Mb
ePub File Size: 9.63 Mb
ISBN: 995-7-33929-782-9
Downloads: 87401
Price: Free* [*Free Regsitration Required]
Uploader: Temi

Interface GPS with Arduino.

The IC is has a wide range of operating voltage from 2. Transmission enable; active low. SPI Module of Arduino. The encoded bit can be obtained from the Dout pin pin This pin has to be connected to Ground 0V to enable the Transmission.

This cycle is repeated as long as TE is kept low. As soon as TE returns to high, the encoder output completes its final cycle and then stops. Pull the Transmission Enable pin pin 14 dxtasheet ground to activate transmission. It is very important that your Decoder should jt12e have this same address for them to talk to each other.

These 12 bits are divided into 8 address bits and 4 data bits.

HT12A/HT12E – Product Details – Holtek

Choosing Motor For Robots. Supply voltage; 5V 2. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. Can be used in Home catasheet for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

  GANGANATH JHA PDF

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. They can also be connected to switches to manually send and receive data. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

HT12E Encoder IC

Connected to the Ground of circuit. These four pins are used to send data, the iin encoded here will be decoded on HT12D IC sharing the same address bits. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

These two ICs together form an Encoder and Decoder pair. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

Can range from 2.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. TL — Programmable Reference Voltage. Choosing Battery for Robots. Adtasheet out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.

  CALIGRAMAS APOLLINAIRE PDF

The primary function of HT12E is to encode a bit and send it out through the output pin. These are the 8-bit address bits, which is used to protect your data.

HT12E Datasheet

The 4-bit data that has ht12ee be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. This oscillator can be used by connecting these two pins through a 1M Resistor.

What is Web Browser. Virgin Galactic — Commercial Space Flight. In this image I on made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. This high-density System-in-Package SiP integrates controller, power switches, and support components.